TennaCAM 2.0 (Fleet or Heavy Equipment) Auxiliary Monitor Installation
Instructions for installing TennaCAM 2.0 Auxiliary Monitor (#TCM-MON2-01) to an existing TennaCAM 2.0 Fleet or TennaCAM 2.0 Heavy Equipment system.
Important! Tenna hardware should only be installed by a mechanic who is Tenna Certified for this specific hardware tracker.
In this article:
Installation Instructions: Adding an Auxiliary Monitor to TennaCAM 2.0 Fleet Auxiliary Camera
Safety Information
WARNING
- Follow established safety precautions for operating and servicing the equipment on which you are installing this Tenna product.
- Do not mount any devices or run any cabling which may interfere with an asset’s safety guards or shields.
CAUTION
- Re-tighten any screws loosened during installation.
- Replace any safety devices removed during installation.
Important Installation Notes
- TennaCAM 2.0 Auxiliary Monitor may only be installed as an accessory to a TennaCAM 2.0 Auxiliary Camera or TennaCAM 2.0 Auxiliary and Side Cameras system.
- Complete the TennaCAM 2.0 Auxiliary Camera and TennaCAM 2.0 Side Cameras (if purchased) installation instructions prior to installing the Auxiliary Monitor.
- Keep asset ignition OFF until instructed otherwise.
Tools and Materials Required
- Cable ties (or similar) to stow away cables neatly and safely
For screw mounting:
- Sheet metal self-tapping screws
- Impact driver and correctly sized driver bit for self-tapping screws
For tape mounting:
- 3M primer pen
- Alcohol wipes
- Cutting tool
Hardware Included
TennaCAM 2.0 Auxiliary Monitor Kit (#TCM-MON2-01) includes:
- TennaCAM 2.0 Auxiliary Monitor
- STSM351PHAR Harness
- Monitor Sun Shield
- U Mounting Bracket
- Duck Foot Mount
- Thumb Screws and Washers
- STSH496 Y Cable
Installation Instructions: Adding Auxiliary Monitor to TennaCAM 2.0 Fleet Auxiliary Camera
Important! The below instructions are for installing an Auxiliary Monitor to a TennaCAM 2.0 Auxiliary Camera only system. If you have installed Side Cameras, skip to Installation Instructions: Adding Auxiliary Monitor to TennaCAM 2.0 Fleet Auxiliary and Side Cameras system.
Installation Diagram
Step 1. Identify an appropriate mounting location.
This should be somewhere inside the cab, on the dashboard, but not obstructing the driver’s view. Do not install the monitor outdoors (or where moisture may land on the monitor within the cabin).
Step 2. Identify the appropriate mount that best fits your installation location
Duck Foot Mount (STSDF1000) or U Bracket Mount (STSU1005).
Step 3. Attach the monitor to the preferred mount.
You may also install the optional sunshield.
Step 4. Mount to the chosen location using appropriate screws for your application.
Step 5. Find a good ignition source and a clean, solid ground connection.
Step 6. Run the monitor’s harness (STSM351PHAR) to the identified ground and ignition sources.
- Connect the monitor harness’ ignition wire (red) to the identified ignition source.
- Connect the monitor harness’ ground wire (black) to the identified ground source.
NOTE: The green and white wires on the monitor harness (marked "Trigger") are not used. Cut off any exposed wire strands. Tape wire ends and tie securely back out of the way.
Step 7. Locate the previously installed DV607 Converter Box (likely installed under the dashboard or the rear wall of the cab).
Run the remaining connections of the Monitor's harness (marked "C1" and "C2") to the DV607.
Step 8. Remove the TennaCAM 2.0 Auxiliary Camera’s video cable (STSH345) connected to the “Video In” port.
Step 9. Plug the TennaCAM 2.0 Auxiliary Camera video cable (that you just unplugged from the DV607 Converter Box) into the female connector (H) of the provided Y Cable (STSH496).
Step 10. Plug one of the male connectors (J) of the Y Cable (STSH496) to the “Video In” port of the DV607.
Step 11. Connect the other male connector (J) of the Y Cable (STSH496) to the “C1” video cable connection on the Monitor’s Harness (STSM351PHAR).
Important! Ensure you connect the Y cable (STSH496) to the "C1" video connection of the monitor’s harness so that the feed shows up on the correct channel/source.
NOTE: The “CAM2” video cable connection on the Monitor’s Harness will not be used.
Step 12. Turn the asset’s ignition on and start the engine.
Let the TennaCAM 2.0 (DV6) camera boot up completely. Then, turn on the monitor to ensure it is functioning properly.
Note: The monitor will need to be turned on by pressing the power button on the monitor for the initial boot up. Once turned on, the monitor will turn on and off via the asset’s ignition. No need to push the power button every trip.
Step 13. Ensure all connections are tight, connector lock nuts are fastened tight, and wires are secured out of the way and away from moving parts.
The monitor installation is complete.
Installation Instructions: Adding an Auxiliary Monitor to TennaCAM 2.0 Fleet Auxiliary Camera and Side Cameras system
Installation Diagram
Step 1. Identify an appropriate mounting location.
This should be somewhere inside the cab, on the dashboard, but not obstructing the driver’s view. Do not install the monitor outdoors (or where moisture may land on the monitor within the cabin).
Step 2. Identify the appropriate mount that best fits your installation location.
Duck Foot Mount (STSDF1000) or U Bracket Mount (STSU1005).
Step 3. Attach the monitor to the preferred mount.
Also, install the optional sun shield if preferred.
Step 4. Mount to the chosen location using appropriate screws for your application.
Step 5. Find a good ignition source and a clean, solid ground connection.
Step 6. Run the monitor’s harness (STSM351PHAR) to the identified ground and ignition sources.
- Connect the monitor harness’ ignition wire (red) to the identified ignition source.
- Connect the monitor harness’ ground wire (black) to the identified ground source.
NOTE: The green and white wires on the monitor harness are not used. Cut off any exposed wire strands. Tape wire ends and tie securely back out of the way.
Step 7. Locate the DV607 Converter Box (likely installed under the dashboard or the rear wall of the cab).
Step 8. Remove the Video Magnification Harness (STSH415) from the port marked “Video In” on the DV607 Converter Box.
Step 9. Plug one of the male connectors (J) of the Y Cable (STSH496) to the “Video In” port of the DV607.
Step 10. Plug the end of the Video Magnification Harness (STSH415) (that you unplugged from the DV607 in Step 7) into the female connector (H) of the Y Cable (STSH496).
Step 11. Connect the other male connector (J) of the Y Cable (STSH496) to the “CAM1” video cable connection on the Monitor’s Harness (STSM351PHAR).
Important! Ensure you connect the Y cable (STSH496) to the "C1" video connection of the monitor’s harness so that the feed shows up on the correct channel/source.
Step 12. Turn the asset’s ignition on and start the engine.
Let the TennaCAM 2.0 (DV6) camera boot up completely. Then, turn on the monitor to ensure it is functioning properly.
Note: The monitor will need to be turned on by pressing the power button on the monitor for the initial boot up. Once turned on, the monitor will turn on and off via the asset’s ignition. No need to push the power button every trip.
Step 13. Ensure all connections are tight and wires are secured out of the way and away from moving parts.
The monitor installation is complete.
Installation Instructions: Adding an Auxiliary Monitor to a TennaCAM 2.0 Heavy Equipment + Auxiliary Camera (1) System
Installation Diagrams
TennaCAM 2.0 Heavy Equipment Auxiliary Camera (1) + Monitor
12-volt System
24-volt System
Step 1. Identify an appropriate mounting location.
This should be somewhere inside the cab, on the dashboard, overhead console, or front windshield, but not obstructing the operator’s view. Do not install the monitor outdoors (or where moisture may land on the monitor within the cabin).
|
|
Step 2. Identify the appropriate mount that best fits your installation location.
Duck Foot Mount (STSDF1000) or U Bracket Mount (STSU1005).
Step 3. Attach the monitor to the preferred mount.
Also, install the optional sun shield if preferred.
Step 4. Mount to the chosen location using appropriate screws for your application.
Step 5. Find and connect to an ignition source and a clean, solid ground connection.
Run the monitor’s harness (STSM351PHAR) to the identified ground and ignition sources.
- For the ignition source, install an add-a-fuse to the monitor harness' ignition wire (red) and connect to the fuse panel.
- Or, splice the monitor harness’ ignition wire (red) together with the TennaCAM 2.0 Heavy Equipment camera’s power harness’ (ROS-BCBL-01) ignition wire (yellow) using the appropriate size butt connector.
- Connect the monitor harness’ ground wire (black) to an available ground wire (black) on the power/ground splitter harness (ROS-BPWR-01).
NOTE: The green and white wires (marked "Trigger") on the monitor harness are not used. Cut off any exposed wire strands. Tape wire ends and tie securely back out of the way.
Step 6. Locate the previously installed DV607 Converter Box.
Remove the TennaCAM 2.0 Heavy Equipment Auxiliary Camera’s video cable (STSH345) connected to the “Video In” port of the DV607 Converter Box.
Step 7. Plug the TennaCAM 2.0 Heavy Equipment Auxiliary Camera video cable (STSH345) (that you just unplugged from the DV607 Converter Box) into the female connector (H) of the provided Y Cable (STSH496).
Step 8. Plug one of the male connectors (J) of the Y Cable (STSH496) to the “Video In” port of the DV607.
Step 9. Connect the other male connector (J) of the Y Cable (STSH496) to the “C1” video cable connection on the Monitor’s Harness (STSM351PHAR).
Important! Ensure you connect the Y cable (STSH496) to the "C1" video connection of the monitor’s harness so that the feed shows up on the correct channel/source.
NOTE: The “C2” video cable connection on the Monitor’s Harness will not be used.
Step 10. Turn the asset’s ignition on and start the engine.
Let the TennaCAM 2.0 (DV6) camera boot up completely.
Turn on the monitor to ensure it is functioning properly.
Note: The monitor will need to be turned on by pressing the power button on the monitor for the initial boot up. Once turned on, the monitor will turn on and off via the asset’s ignition. No need to push the power button every trip.
Step 11. Ensure all connections are tight, connector lock nuts are fastened tight, and wires are secured out of the way and away from moving parts.
The monitor installation is complete.
Installation Instructions: Adding an Auxiliary Monitor to a TennaCAM 2.0 Heavy Equipment + Auxiliary Camera (3) System
TennaCAM 2.0 Heavy Equipment Auxiliary Camera (3) + Monitor
12-volt System
24-volt System
Step 1. Identify an appropriate mounting location.
This should be somewhere inside the cab, on the dashboard, overhead console, or front windshield, but not obstructing the driver’s view. Do not install the monitor outdoors (or where moisture may land on the monitor within the cabin).
|
|
Step 2. Identify the appropriate mount that best fits your installation location.
Duck Foot Mount (STSDF1000) or U Bracket Mount (STSU1005).
Step 3. Attach the monitor to the preferred mount.
Also, install the optional sun shield if preferred.
Step 4. Mount to the chosen location using appropriate screws for your application.
Step 5. Find and connect to an ignition source and a clean, solid ground connection.
Run the monitor’s harness (STSM351PHAR) to the identified ground and ignition sources.
- For the ignition source, install an add-a-fuse to the monitor harness' ignition wire (red) and connect to the fuse panel.
- Or, splice the monitor harness’ ignition wire (red) together with the TennaCAM 2.0 Heavy Equipment camera’s power harness’ (ROS-BCBL-01) ignition wire (yellow) using the appropriate size butt connector.
- Connect the monitor harness’ ground wire (black) to an available ground wire (black) on the power/ground splitter harness (ROS-BPWR-01).
NOTE: The green and white wires (marked "Trigger") on the monitor harness are not used. Cut off any exposed wire strands. Tape wire ends and tie securely back out of the way.
Step 6. Locate the DV607 Converter Box (likely installed under the dashboard or the rear wall of the cab).
Step 7. Remove the Video Magnification Harness (STSH415) from the port marked “Video In” on the DV607 Converter Box.
Step 8. Plug one of the male connectors (J) of the Y Cable (STSH496) to the “Video In” port of the DV607.
Step 9. Plug the end of the Video Magnification Harness (STSH415) (that you unplugged from the DV607 in Step 8) into the female connector (H) of the Y Cable (STSH496).
Step 10. Connect the other male connector (J) of the Y Cable (STSH496) to the “C1” video cable connection on the Monitor’s Harness (STSM351PHAR).
Important! Ensure you connect the Y cable (STSH496) to the "C1" video connection of the monitor’s harness so that the feed shows up on the correct channel/source.
Step 11. Turn the asset’s ignition on and start the engine.
Let the TennaCAM 2.0 (DV6) camera boot up completely. Then, turn on the monitor to ensure it is functioning properly.
Note: The monitor will need to be turned on by pressing the power button on the monitor for the initial boot up. Once turned on, the monitor will turn on and off via the asset’s ignition. No need to push the power button every trip.
Step 12. Ensure all connections are tight and wires are secured out of the way and away from moving parts.
The monitor installation is complete.